8 drops is A LOT so fast.
I'm surprised you're not Herxing.
Although, if a Mold or Fungus is stopping the ClO2 from working that would make sense.
So that immediately makes me go, "Hmm....". And question what is going on.
WHY aren't you Herxing with 8 drops so fast?
"Everyone's Different", so it COULD be that.
You need to be careful. If the Mold/Fungus Protocol works, and the ClO2 'suddenly starts working',
you could severely Herx. (if that's what's going on)
I usually drop down to 1 to 3 drops (from 5) when I realize that it has stopped working again and
I need to do the Mold/Fungus Protocol, just to be "safe".
JH suggests you stop where you're at (whatever protocol), although that doesn't sound like
a good idea to me, because of the scenario I described above. (?)
Maybe the potential Mold/Fungus issue isn't so severe as I think it could be.
I suppose Pascalite Clay is okay. It's supposed to be a Calcium Bentonite | Montmorillonite Clay.
So I assume it is working. I've only used the clay I get from my source, which I know works.
If your source is cheating and not using the correct clay, that would be a problem.
I wouldn't use S.Pellegrino. It is a mineral water, which means it has a lot of who knows what
kind of minerals in it. I suppose if you put some MMS/CDS in it and test it with ClO2 Test Strips
and it tests okay, then it should be okay. I use pure Seltzer Water from a can.
Although, if you are ONLY taking clay without the MMS, it's should be fine. (early protocol)
And I wouldn't use it if I was taking DMSO. I don't take a chance on anything mixing with the
ClO2 and causing some kind of a chemical reaction, or having something that might be in it
shooting throughout my body with the DMSO, although there could be similar concerns with
what's in the Clay. (?) I've never read anyone saying, "It's not a problem", although I suppose
JH is implying that. (?)
I just like to be as careful as possible.
That's the reason we are supposed to ideally use STEAM Distilled Water is because it is
completely "clean" and non-reactive. (and I think 'pure' Seltzer Water similarly)
Anyway, maybe you have a SEVERE Mold/Fungus issue?
(I think BioFilm could be an issue, as well)
And it will take some time to clear that before you will see results from ClO2?
I suppose that's possible.
I can't think of anything else you could do other than follow the protocols as per JH
and hopefully they will kick in at some point.
It sounds like you are eating and drinking well, so that shouldn't be negatively affecting
the ClO2. (chocolate, caffeine, alcohol, citrus, etc. -- I'm not sure what "food/drink"
that is high in antioxidants would maybe cause an issue --- JH mentions that, or
maybe only as a "supplements", I forget, but doesn't list actual foods (that I remember),
or any real levels other than the "high in" descriptor)
Before you go to 8 drops, I think you should have gone to Protocol 1000+ with DMSO.
This should pretty much be done at about 3 (to 5?) drops.
Again, Low and Slow with the DMSO drops, and see if that makes a difference.
And then increase the ClO2 drops after you've done 1000+ for probably at least
a week or two or so.
It's a definite vexing quandary.
Maybe someone else will notice something or have an idea.
Other than that, just keep on and see what happens.
(have you been COVID-19 Vaccinated? I've been wondering lately if that
is maybe interfering with the ClO2 from working, but I haven't seen anything
where people are definitively saying one way or another --- and even then
I have to take it with a grain of salt from most people, unfortunately ---
plus it's anecdotal, and are there any good sources of reliable info, etc.....)
Let us know if something changes or you figure something out.