TOPIC:

Is 3 Drops of Uncativated MMS per liter of water corrosive? 22 Jul 2020 15:09 #65290

compujohnny Topic Author Offline New Member Posts: 9 Thank you received: 3	Hi, I have a water dispenser and I am adding unactivated MMS to the water 2 - 3 drops per liter plus 5 ml CDS (3000 ppm) per liter, but the internal container is stainless, and I am worried that it may be corrosive, Is unactivated MMS and CDS in after diluting them still corrosive? What harm can happen if it is and you drink the water? Thanks in advance for your help
	Please Log in or Create an account to join the conversation.

Is 3 Drops of Uncativated MMS per liter of water corrosive? 22 Jul 2020 20:46 #65301

CLO2 Offline Administrator Posts: 5561 Thank you received: 4393	CDS should not be a problem, but MMS might be as it is very alkaline. However, looking at a stainless steel chemical compatible chart, sodium chlorite was rated "A" (excellent, no effect), so it may not be a problem at all. The chart did not say if sodium chlorite was in dry form or wet, as we use it. The following user(s) said Thank You: compujohnny
	Please Log in or Create an account to join the conversation.

Is 3 Drops of Uncativated MMS per liter of water corrosive? 23 Jul 2020 22:22 #65318

compujohnny Topic Author Offline New Member Posts: 9 Thank you received: 3	Thanks for your response, I have tested the water ph and after adding 2 drops of MMS + 5 ml of CDS per liter the ph is anywhere from 6 - 7, so not very alkaline I know MMS corrodes stainless at 20%+, My question is does it corrode at a much lower concentration like the one I am using? Please note that this is intended to be used long term so I need to make sure it's safe
	Please Log in or Create an account to join the conversation.

Is 3 Drops of Uncativated MMS per liter of water corrosive? 23 Jul 2020 22:28 #65319

paul Offline Platinum Member Posts: 618 Thank you received: 670	yes. clo2 dissolves metal (oxidizes metal to a soluble salt). That's why all the MMS literature says 'no metal'!
	Please Log in or Create an account to join the conversation.

Is 3 Drops of Uncativated MMS per liter of water corrosive? 24 Jul 2020 00:21 #65322

CLO2 Offline Administrator Posts: 5561 Thank you received: 4393	CLO2 and NaCLo2 may effect stainless steel differently. Best to look up chlorine dioxide and sodium chlorite water solutions online for compatibility.
	Please Log in or Create an account to join the conversation.

Page:
1

Index

General Discussion

Is 3 Drops of Uncativated MMS per liter of water corrosive?

Disclaimer: This forum provides general information and discussion about medicine, health and related subjects. The words and other content provided in this forum, and in any linked materials, are not intended and should not be construed as medical advice. If the reader or any other person has a medical concern, you should consult with an appropriate licensed Physician or other Health Care provider. Never disregard professional medical advice or delay in seeking it because of something you have read on this forum or any other linked materials. If you think you may have a medical emergency call your Doctor or 911 immediately.

The views expressed on this forum and website have no relations to any academic, hospital, practice or other institutions. This website is at times monitored. Anything the host finds offensive may be removed at his discretion. The host disclaims responsibility for anything posted by third-parties. Any statements on this forum/website related to Chlorine Dioxide, MMS or variations are not FDA approved to diagnose, cure, mitigate, treat, or prevent any disease.

MMS (Master Mineral Solution) is Sodium Chlorite 28% (22.4% Sodium Chlorite, 5.6% Inert Salts and the remainder water) plus an acidic activator (usually 50% Citric Acid or 4% Hydrochloric Acid) when combined produces Chlorine Dioxide.

License: Except where otherwise noted, content on this site is licensed under a Creative Commons Attribution-NonCommercial-NoDerivs 3.0 Unported License.