TOPIC:

I have 2 bottles and only tested the PPM on the first bottle in line(the first in line of the series). The first bottle now contains less than the original 300ml started with. The second bottle contains a bit more than 300ml since I poured the completed reactor solution from each cook into the 2nd bottle(bad idea?). I think I will run one more cook, use both receivers, test each separately and if the PPM is high enough in both, combine the two bottles into one big one(~650ml) and then retest, which is NOW a lot easier(thanks Pam)since I'm not counting drops.

My critical thinking is lacking in logic sometimes so I would appreciate some review and suggestions.

I poured the reactor solution in bottle #2...you think it will skew the PPM and make the reading unreliable?

This next comment will bring to full display my rookie status:


"PPM is PPM" no matter the source, unless we are worried/concerned about an unknown effect of mixing MMS & CDS
with a caveat of the possibility of the MMS causing stomach discomfort.

Latest update. 11/13..1:30p

Upgraded the batch again. Weighted all solids, Measured 3 tsp of DW, Sealed all tubing, hovered the exit tube above the solution in the reactor chamber.

PPM test ratio of 100ml Distilled Water to 1ml of solution

The first bottle in sequence shading is just low of 50
The second bottle in sequence shading is right on 10

At what rate should the contents of bottle #1 be applied? Would Bottle #1 solution be considered equal to 5 drops of MMS(activated) while #2 equal to 1 to 1 MMS, or have I screwed #2 PPM equation up by pouring the remaining contents of the reactor solution in bottle #2?

Ain't this fun!!

Welcome to the fun we had when CDS first came out and we were all running around testing and trying to figure it out. I was excited when the shotglass method came out, since I had friends who could do that, with it's pretty well guaranteed ppm per dose, vs some of the other methods. I'll let charlotte answer your question, since I'm not up on the 3 minute procedure.

OK...#2 is tossed...the wife hates the Sycamore Tree the neighbor planted on the property line(leaves as big as pie plates). What pray tell, is the most useful dilution I should/could make?

OK...say one is looking to use Protocol 2000+

Alrighty Then...Correct me if I'm wrong.

1ml of 3000ppm CDS = 3 drops of activated MMS1
If using both MMS1 & CDS, each time you up the dosage for MMS...up the dosage for CDS accordingly(if tolerated)
If MMS2 is in the mix...start out slow(1 grain per "00") and work up to 1/2 full size "00"

So...say if you are up to 9 drops MMS1 per dose that would be 3ml CDS per dose. For a 8 hr dose in a 32oz bottle, mark the bottle into 8 sections and add either 72 drops of MMS1 or 24 ml of cds. For a 12 hour dose mark the bottle into 12 sections and add 108 drops of MMS1 or 36ml of CDS. Is there any penalty for adding additional water to a dose and the mixture is complete and prior to drinking?

If using DMSO...add separately and prior to individual dose in the same drops of MMS1. So if you have made a 8 hr supply of MMS1 @ 9 drops per hour/or 72 drops per 8 hour dose, the DSMO per serving would be 9 drops.

What is the dosage of DSMO with oral CDS?

Topical Application

I have read that MMS1 should go on skin first...followed by equal DSMO//// I have read mix equal parts MMS1/DSMO and apply up to 1 1/2 oz.
I have read to alternate topical applications with CDS/DSMO without ratio stated(no help at all)

Now...add diet with the do's and don'ts, and off you go!

Hopefully this is all correct...but if not please advise.

vector wrote:

Alrighty Then...Correct me if I'm wrong.

1ml of 3000ppm CDS = 3 drops of activated MMS1 Yes
If using both MMS1 & CDS, each time you up the dosage for MMS...up the dosage for CDS accordingly(if tolerated) Yes
If MMS2 is in the mix...start out slow(1 grain per "00") and work up to 1/2 full size "00" No, max size is 1/2 a full size "0" (which is smaller than a 00)

So...say if you are up to 9 drops MMS1 per dose that would be 3ml CDS per dose. For an 8 hr dose in a 32oz bottle, mark the bottle into 8 sections and add either 72 drops of MMS1 or 24 ml of cds. Yes

For a 12 hour dose mark the bottle into 12 sections and add 108 drops of MMS1 or 36ml of CDS. Is there any penalty for adding additional water to a dose and the mixture is complete and prior to drinking? You should definitely add additional water to your dose before drinking, particularly if you're doing it in the 12 high-drop doses. Try to get 4 oz of water with each dose, because the dose is so high - a good clue that you need more water is if you find a slight burning in the back of your throat

If using DMSO...add separately and prior to individual dose in the same drops of MMS1. So if you have made a 8 hr supply of MMS1 @ 9 drops per hour/or 72 drops per 8 hour dose, the DSMO per serving would be 9 drops. Yes

What is the dosage of DSMO with oral CDS? drop equivalent as with MMS1, work up slowly, as you do with MMS1

Topical Application

I have read that MMS1 should go on skin first...followed by equal DSMO//// I have read mix equal parts MMS1/DSMO and apply up to 1 1/2 oz.
I have read to alternate topical applications with CDS/DSMO without ratio stated(no help at all) If you are making a skin spray that will be used over time, you do not want to put your DMSO into the spray (mix it all together) because the DMSO will "kill" the MMS over time - you can mix at the time you are using it (after the MMS has been activated, so you have all the chemical reactions completed) Most people that I know use the spray, and then rub "some" or the same amount of spray on top of the spray. Michael Harrah has Protocol 3000 on his website

Now...add diet with the do's and don'ts, and off you go!

Hopefully this is all correct...but if not please advise.

Thank You Pamela...