TOPIC:

Hi all,

I started with MMS on 1st of August but I am going really slow as there is a lot to heal. I know I have a lot of viruses, parasites and need a lot of detoxification. On the first day I started with 1/4th of a drop and stopped on the second because of a severe pain at my liver. Then restarted with 1/8th of a drop, went up to 1 drop and I am now back at 1/2 of a drop as I have some nausea and liver pain. As you can see I am going really slow. The reason I started with MMS was a testicular tumor the doctor found on me. From what I read on Jim Humble's book, for my case I need to reach Protocol 2000. Considering the speed of things so far it seems that I will reach that protocol (high doses, DMSO and MMS2) in 3 months time. As a result I am considering alternatives to help the part of my body that needs most attention right now.

I am considering MMS baths. The trouble with that is I am at a place (a small island) where I don't have any reverse osmosis filter installed and the market does not have drinkable distilled water. I make distilled water with a machine but it can make a maximum of 10-12 liters per day and from that we use at least 5 liters for our daily needs.

I was wondering if I instead can use a smaller amount of water like a bowl with a liter or two and dip my testicles in. I understand that it is not that practical but I have to try to see if I can do it. However my challenge and the reason I write this is for someone with more experience to share his/her view if this will help and also to recommend a number of drops per liter used or some other kind of measurement in order to consider the number of drops.

Another recommendation is to rub DMSO with MMS on the area but I want to stay away from DMSO for now as my liver is weak and it might lead to an allergic reaction.

Also if you have any other recommendations for my case please feel free to share.

Thank you for taking the time to read and help me out.

lobby44, for topical use of MMS, it might be more appropriate to use CDS or CDH instead of MMS1 because there is much more CLO2 available.

MMS1 contains about 10% of the available CLO2 in MMS when used externally, while CDH has 50% and CDS has 100%.

You could dilute CDS or CDH and spray your testicles or dip them into a water solution in a small container.

Also consider using the Bag Protocol (CLO2 gas), either full body or just testicles, or the external MRSA Protocol.

Thank you for the reply CLO2.

I've seen the video and understood what CDH is. I didn't know about CDS as well but found some info on Jim Humble's latest book. Could you please direct me of how I can make CDS? Or is it a ready solution that I have to buy?

I will definitely start with CDH tomorrow! Any pointers on how many times I spray or how much time I dip? Again, thank you for the information.

I have not had time to make a video slide-show on how-to-make CDS, but I do have this PDF file that may help you in making your own CDS.

CDS should have only chlorine dioxide gas (CLO2) in a water solution and no residual MMS or activator. If you want higher CLO2 concentration than 3000 ppm, just use the same CDS and add new ingredients in the reactor container and again let it activate overnight or 12+ hours as normally done to make CDS the easy, safe way.

Jim's book does not have a dosing comparison of CDS and CDH to MMS1, so here are two charts that do have that information.

Regarding dosing for your situation, I can only say start low and slowly increase.

Thank you.

It seems that it is difficult for me to create CDS so I will order a ready solution.

For now I will create CDH. I am wondering, for the teaspons do I use a metallic teaspon? Is it fine or MMS or the acid will react to it?

I also do the procedure quickly (cap the bottle asap) as gas will be released correct? Also won't the bottle create a lot of pressure? I will use a half liter bottle which will have some space though.

Found more extensive instructions you posted in the past and made it. Thank you

Metal measuring spoons might be okay if they are stainless steel because the chemicals are in contact with the metal for only a few seconds. But, plastic may be a better choice. If you can find some syringes, they work fine. You don't need needles for the syringes.

Dosing CDH and CDS is done using milliliters, so you may want to get some syringes anyway. An animal feed store will have them if you have such a store where you are living.

CDS is not difficult to make once you have the appropriate containers. If you use containers other than what I used for testing, the CLO2 ppm will probably be different. You can measure the CLO2 ppm using CLO2 test strips.

How many times do I spray the CDH solution in a day?

Is it like one time every hour for 8 hours?

If you follow Protocol 3000, without the DMSO, you would mix 10 ml of CDH (as per my conversion chart) with some additional water. The protocol calls for adding 20 drops of water, but that is when you use MMS1. And, application is not with a spray bottle; it is by hand.

So, you can follow the idea of Protocol 3000, but modify it for use with CDH and a spray bottle.

You will need enough solution for the spray bottle to work. I would start low and if no irritation, then increase CDH the next batch you make. If you start with 1 ml of CDH (3000 ppm CLO2) mixed with 9 ml of water, then you will have 300 ppm CLO2. If that recipe works without any problems, then increase to 2 ml of CDH in 9 ml of water, etc. You will know when the dosage is too high!